Mold Temperature Controller Manufacturer | Mold Temperature Controller Selection Skills

Feb 21, 2022

Leave a message

More and more plastic manufacturers have deeply realized the importance of using a mold temperature machine to control the temperature of the mold for the molding of plastic products. If the selected mold temperature machine is consistent with the temperature requirements of product molding. Can greatly improve the quality of products. This in turn reduces the operating cost of the product. So how to choose a mold temperature machine that matches your needs?

 

With the intensification of market competition, plastic manufacturers are paying more and more attention to this issue. What kind of mold temperature machine is required for humidity control in each stage of product molding? What are the advantages and disadvantages of this type of mold temperature machine? According to the similarities of the mold temperature machines, comparing the mold temperature machines sold by different manufacturers on the market, it is not difficult for us to classify them into several series. The classification criteria are: heat transfer medium, temperature control range, internal structure, cooling method, etc. The above criteria play a key role in selecting a mold temperature machine.

 

1. Advantages and disadvantages of mold temperature machine

Undoubtedly, we can find a mold temperature machine that matches your needs in the market, considering various aspects of economy and technology. But in fact, how to choose from a variety of brands and series is not an easy task. In addition to considering the cost, it is also necessary to understand: the timeliness of product supply, the quality of after-sales service, whether the machine can be expanded, etc. In fact, what is important to you is to obtain the technical parameters of the mold temperature machine that suits your needs, so as to measure the availability to you.

 

1. Thermally conductive medium as standard

To decide whether to use heat transfer oil or water. Within the allowable temperature control range, based on the good thermal conductivity of water, the water type is preferred.

 

(1) Water-type mold temperature machine

When the temperature requirement of the mold does not exceed 95 °C, the working mode of the mold temperature machine is non-closed; when the temperature is higher than 95 °C, the closed working mode must be selected to ensure a certain pressure inside the system and avoid the evaporation of the heat transfer medium.

When the mold is at high temperature, such as thermoplastic materials in the process of injection molding, precise and rapid heat conduction is necessary. This is a concern for products with high precision requirements. Based on the limitation of the internal space of the hot runner of the general type of mold, the hot water type mold temperature machine is more suitable than the oil type mold temperature machine. When the temperature reaches 200°C and the pressure is 16Bar, the water-type mold temperature machine is more prominent.

The temperature control range of the water-type mold temperature machine is: 5℃~200℃.

 

(2) Oil-type mold temperature machine

The temperature control range of the oil-type mold temperature machine is 45℃~350℃. According to the temperature control requirements you need, Hengrui Machinery provides a variety of series for you to choose.

The temperature of the non-closed oil-type mold temperature machine can reach as high as 200 degrees. Considering that some thermally conductive media will undergo pyrolysis at 200 °C. Therefore, the heat transfer medium used in this series of mold temperature machines should have a temperature higher than 200 °C for pyrolysis reaction, so as to prevent the pyrolysis reaction from locking the decomposed carbon to the surface of the heat medium, thus reducing the heat transfer performance of the medium and eventually making the mold The humidity cannot be well controlled.

 

Because oil is prone to pyrolysis at high temperature, safety measures should be taken to avoid the pyrolysis reaction when the oil temperature is higher than 200 °C. If necessary, the flow rate of the heat transfer medium should be checked. If the flow rate is too low, the system should automatically shutdown function.

In addition, the problem of oxidation of the thermally conductive medium should be avoided. The oxidation reaction will increase the viscosity of the medium, reduce the thermal conductivity of the medium, and also affect the temperature control of the mold. Therefore, when pouring oil into the oil tank, the oil must be poured slowly, and the temperature of the medium should be controlled at about 100 °C.

 

2. Cooling method, the second selection criterion

When choosing a machine, it is also necessary to pay attention to the cooling method of the heat transfer medium. There are two types of cooling methods: direct and indirect. In the indirect cooling method, the cooling circuit is separated from the main circuit. The heat transfer medium used in this cooling method is generally oil type. The heat of the cooling medium is absorbed by the heat medium and directly enters the exchange valve. The indirect cooling method is only used on the oil-type mold temperature machine. Because the cooling capacity of this cooling method is not strong, the cooling water must be kept clean when using this cooling method, so as to prevent impurities from blocking the pipes and affecting the temperature control performance of the machine. .

 

Disadvantage of indirect cooling: heat is lost in the heat exchanger. Therefore, when the actual temperature of the medium has a large deviation from the set value, we use the direct cooling method with a large cooling capacity. With direct cooling, the cooling water goes directly into the circuit without the need for a heat exchanger. Using this cooling method can greatly improve the cooling capacity of the system, and then the heat transfer medium can be rapidly cooled. Electric valve or multi-stage solenoid valve control can be used to increase the control accuracy of the system. The premise of using the direct cooling method is: closed circuit; the heat transfer medium needs to use clean water.

 

3. Single-loop, double-loop, multi-loop control system, the third selection criteria

To distinguish what is a single-loop, dual-loop and multi-loop control system.

The single-loop control system is compact in structure and small in size. There are various series according to its temperature control range.

 

The dual-loop control system is used when the temperature required by the moving and fixed mold plates of the mold is different. According to the different temperature requirements of the two templates, the temperature of the two circuits is controlled and the flow rate of the pump is adjusted.

 

Nanjing RICOM Refrigeration Equipment Co., Ltd. is a manufacturer specializing in industrial temperature control technology for 20 years. It implements the modern quality management system S09001: 2008 and environmental system IS014001: 2004 standards to ensure that the enterprise team continues to be in the technical field. Innovation, focusing on customer's sense of use and satisfaction, has been unanimously recognized by the industry and customers; obtained AAA credit rating certification; in 2016, the company was a contract and trustworthy enterprise. In 2013, the company established a chiller in the Chuzhou Economic and Technological Development Zone at the foot of the beautiful Langya Mountain. And mold temperature machine production base, and established Chuzhou Ruikang Plastic Technology Co., Ltd.


Contact us today!


Send Inquiry
Send Inquiry